gear rail Gear Rail – SynthRISE

gear rail Gear Rail – SynthRISEAll new Gear Rail Mk2 and SubPiggy Mk2 coming soon! Completely redesigned for adjustability, expandability, and greater load capacity. We are very excited to bring this major upgrade to fruition. Production units will begin shipping at the end of November. For a product launch announcement, keep an eye on our Instagram account or message us on our contact form. This is the desktop cousin of our innovative SubPiggy stand. Unlike the SubPiggy, the Gear

All-new Gear Rail Mk2 and SubPiggy Mk2 coming soon! Completely redesigned for adjustability, expandability, and greater load capacity.  We are very excited to bring this major upgrade to fruition.  Production units will begin shipping at the end of November.  For a product launch announcement, keep an eye on our Instagram account or message us on our contact form.

This is the desktop cousin of our innovative SubPiggy stand. Unlike the SubPiggy, the Gear Rail doesn't contact the synth. It's ideal for holding Eurorack skiffs above CV ports of the Matriarch, Grandmother, Pro-2,  Pro-3, Matrixbrute, Minibrute 2, Waldorf KB37, minilogue and many others. It can make performing and playing much easier by allowing you to place fx pedals, a controller keyboard, desktop synth, looper, drum machine, laptop or tablet within easy reach of a large synth's control panel. You can even use it to hold outboard gear above the back edge of a 32 channel mixer!

Gear support arms on the Gear Rail can be easily repositioned or rearranged and then locked in place. Add or remove support arms as your needs change.  Or change the length of the Gear Rail with our Tube Extender Kit.

Features:

• Lengths to fit almost any 25 to 49 key synth (26.625" is for Grandmother).  Greater lengths possible with our Gear Rail Tube Extender Kit
• Maximum total weight of gear on Gear Rail is 6.8 kg (15 lb). You can exceed this weight limit if you're careful not to push or pull on the fully loaded stand.
  
• Gear support arms are 6.75" deep and are available angled or flat (horizontal).
• Thick rubber trim prevents gear from sliding around on the arms.
• Angled arms can hold: Deluge, Reface, iPad, and much more
• Decksavers compatible

Fits on angled or flat arms:

• Moog Mother-32, DFAM, Subharmonicon
• Behringer Neutron, Model D, Wasp Deluxe, Cat, K-2, Pro-1
• Elektron boxes (all models)
• Hydrasynth desktop
• RD-8
• MicroFreak
  
• Yamaha Reface (requires HE-2 hook extenders)
• RC-505, RC-202, TR-8 (original version), MX-1, TB-3, VT-3 (requires HE-2 hook extenders)
• TR-8S (tendency to tip backwards; only install if there's a wall immediately behind it)

Fits only on flat arms:

• TR-808, TR-909
  
• Maschine, MPC, minikey keyboard, and much more
• Korg Minilogue
• Minibrute, Microbrute

Dimensions:

• Flat Arms: 8.12" (206 mm) table to bottom of gear
• Angled Arms: 7.69" (195 mm) table to bottom front of gear; 34 degree angle. 11.47" (291 mm) table to upper rear corner of support arm
• Side panels that contact table or desk:  9.4" (240 mm) deep

Optional Accessories:

• Extra pair of angled support arms
• Extra pair of flat support arms
• Gear Rail Tube Extender Kit
• Expansion Shelf (medium or large).  Can fit on angled or flat arms.
• Volca Tray Shelf

Includes:

• (2) end panels
• (4) support arms with locking collars (specify angled or flat arms when ordering)
• (2) rigid support tubes
• (4) steel/plastic knobs